Underpinning advice

Wall ties: the failure nobody checks

Published

Most people who call us about a bulging brick wall are already bracing for the worst number. A wall that’s visibly out of plumb sounds like a foundation has failed, and foundation repair is the expensive end of this trade. So it’s worth saying plainly, early: a genuinely common cause of a bulging brick wall has nothing to do with the ground underneath it, costs a few thousand dollars to fix rather than tens of thousands, and is caused by a component most homeowners have never heard of and will never see.

What a wall tie actually does

If your house is brick veneer or cavity brick — which covers the overwhelming majority of Melbourne homes built from the 1920s onward — the brickwork you can see from the street isn’t carrying the house. In brick veneer, a timber or steel frame does the structural work, and the brick skin outside it is a weatherproof, decorative layer with a cavity gap behind it. In cavity brick, two masonry skins stand side by side with a gap between them. Either way, that outer skin is tall, thin, and unstable entirely on its own — a single-brick-thick wall several metres high has almost no ability to stand up straight by itself in wind.

What holds it upright is a row of small metal ties, usually galvanised steel, built into the mortar joints every few courses and spanning the cavity to anchor the brick skin back to the frame or the inner leaf. There might be a hundred or more of them across a single elevation. Nobody thinks about them, because once they’re bricked in they’re invisible for the life of the house — right up until enough of them have failed that the wall they were restraining starts to move.

Why they fail, and why it’s slow and silent

Galvanised steel ties are coated in zinc to resist corrosion, and that coating has a service life — commonly estimated at somewhere between 25 and 60 years depending on the coating thickness, the tie design, and how much moisture sits in the cavity over that time. Older tie types used through the mid-20th century generally had thinner coatings and shorter working lives than what’s specified today, and plenty of houses built from the 1950s through the 1980s are now sitting right in the window where that original galvanising has run out.

Moisture is what actually does the damage, and a cavity holds more of it than people assume. Weep holes block with mortar droppings or garden mulch, cavity flashing fails, a cracked render or a blocked gutter sends water down the inside face of the outer skin for years, and the cavity — meant to let that moisture drain and ventilate away — instead stays damp. A tie sitting in a permanently damp cavity corrodes faster than the manufacturer’s rated life assumed, sometimes by decades.

Once a tie’s coating is gone, the steel underneath rusts, swells, and eventually loses its grip in the mortar or snaps outright. This doesn’t happen as one dramatic event — it happens to one tie, then another, scattered across the wall over years, with absolutely nothing visible from either side of the brickwork while it’s underway. The first sign anyone actually sees is the day the wall has lost enough of its ties that the remaining ones can no longer hold the skin flat, and it starts to belly outward under its own weight and the wind load it’s carrying.

The tell that separates it from a footing problem

This is the part worth getting right before anyone spends money, because the two causes look similar from a distance and call for completely different repairs.

Failed wall ties produce a bulge — a gentle, even curve outward through the middle of the wall, roughly between the window heads and the sills, where the bricks have the least restraint. The base of the wall, where it meets the ground, and the top, where it meets the eaves, generally stay put. You’ll often see a horizontal crack line at a fairly consistent height along a mortar joint, which roughly marks where a row of ties has let go. Crucially, the floors inside stay level, the doors keep closing properly, and there’s no stair-step cracking working its way diagonally through the brickwork. The wall is moving; the house underneath it is not.

Footing or foundation movement tilts the whole wall as one plane rather than bulging the middle of it, and it rarely travels alone. Stair-step cracks run diagonally through the mortar joints, usually from a window or door corner, and you’ll generally find matching evidence elsewhere in the house — a sloping floor, a door that’s started sticking, a cornice crack that keeps reopening. If a wall is leaning as a straight plane and the rest of the house agrees with it, that’s the ground moving, not the ties, and it belongs on our underpinning page rather than here.

Plenty of houses genuinely have both things happening at once, in different places or even on the same wall, which is exactly why a proper assessment measures rather than assumes. Our leaning and bowing walls page covers all four causes we see in that category, with the full process for reading the difference — plumb readings at several heights, the crack pattern, and a borescope or tie detector run through a drilled mortar joint to see what’s actually left of the ties inside.

What the repair actually costs

This is where the gap between what people fear and what it usually costs is largest. Re-tying a bulging brick skin uses helical stainless steel ties, driven or screwed in from outside through small holes drilled in the mortar joints and anchored into the frame or inner leaf behind. The holes are then repointed, so the finished wall looks untouched. It’s installed from the outside with no need to open up the wall from inside, it typically runs $3,000 to $9,000 for a standard elevation depending on wall area and tie spacing, and most jobs are done in a day. Where the brickwork has deteriorated further — bricks that have shifted relative to each other, mortar that’s lost its bond, or a bulge severe enough that straightening isn’t realistic — a partial rebuild or an engineered lateral restraint system is the honest answer instead, and that runs considerably higher, in the $8,000 to $25,000 range.

Compare that against footing repair or underpinning for genuine foundation movement, which commonly runs $15,000 to $40,000 across a typical affected section. That gap is the whole reason getting the diagnosis right before accepting a quote matters as much as it does. We’d rather tell a caller their wall needs $4,000 of remedial ties than let them sign up for a footing job they don’t need — and we see the mistake made in both directions often enough that it’s worth saying out loud.

Where this shows up around Melbourne

Tie failure isn’t suburb-specific the way reactive clay is — it tracks the age of the housing stock and how wet the cavity has stayed over the decades, which means it turns up across the metro area wherever brick veneer from the 1950s through the 1980s is now sitting past the original galvanising’s working life. It’s a genuinely common finding in the established brick-veneer streets of Werribee, where a good share of the housing near the town centre dates from the 1960s to the 1980s and has had forty to sixty years for an original tie system to run down. Hoppers Crossing, built out largely through the 1980s and early 90s, sits in a similar age band, and Deer Park carries a substantial body of 1970s and 80s brick veneer alongside its newer estates — exactly the vintage where this becomes worth checking, independent of whatever the ground underneath is doing.

In every one of those suburbs the right first step is the same: read the bulge and the crack pattern before assuming it’s the footings, because the two repairs aren’t in the same cost bracket and only one of them needs the ground touched at all.

The honest version of what to do next

A bulging brick wall is worth looking at promptly rather than left to make its own case — if the bulge is increasing, if bricks have visibly shifted against each other, or if it’s above a doorway or anywhere people stand, that’s a same-week call rather than a wait-and-see. But promptly doesn’t mean expensively. Plumb readings, a look at the crack pattern, and a borescope check through a couple of mortar joints will usually tell you within an hour whether you’re looking at a $4,000 fix or something that needs the ground addressed — and that’s the one piece of information worth having before anyone accepts a number.


Got a bulging or leaning brick wall and want to know which repair it actually needs? Book a free assessment — we’ll check the ties, read the crack pattern, and tell you honestly which side of the cost range you’re on.

Common questions

How do I know if my wall ties have failed without opening up the wall?

You can get most of the way there without any demolition. Stand back from the wall and sight along it in low, raking light — a tie failure shows as a gentle, even bulge through the middle of the wall, usually between the window lines, with the top and bottom still sitting where they should. A horizontal crack at a consistent height along a mortar joint is another strong sign, since that's roughly where a row of ties would be. The part you can't see from the ground is how many ties are actually left intact, and that needs either a borescope through a drilled mortar joint or a tie detector run along the wall — a five-minute check for anyone doing the assessment, and far cheaper than guessing.

Can I just repoint or patch a bulging wall myself instead of fixing the ties?

You can patch the mortar, but it doesn't address what's actually wrong, and on a genuine tie failure the bulge will keep moving regardless of how fresh the pointing looks. The outer skin has lost its mechanical connection to the frame behind it, so nothing is holding it vertical except its own weight and the bond between bricks — cosmetic repair doesn't restore that. Worse, a wall with no remaining restraint is one strong wind gust away from a real safety problem, which is not something to leave patched over for appearance. Re-tying is a half-day job for a trade that does it regularly and it's the one part of this repair that's genuinely inexpensive — there's not much upside in skipping it.

Does a tie failure mean termites got into the frame behind the brickwork?

Not directly — wall ties are galvanised steel, and corrosion and termite damage are two separate problems with two separate causes, even though both can be present in an older cavity wall. That said, a cavity with corroding ties is usually a cavity that's been holding moisture for years, and persistent moisture against a timber frame is exactly the condition termites prefer. If a borescope inspection to check the ties is happening anyway, it costs nothing extra to have the same inspector look at the timber plate and studs right behind the brick skin while they're in there, rather than treating the two as unrelated questions.

Think this is happening at your place?

We assess before we quote — floor levels measured, cracks mapped, and a straight answer on whether you need work at all. Read more aboutunderpinning & foundation repair, or get in touch.

← All foundation advice

Call 03 4149 0244Get a quote